CURB STOPS
MFG. # H-10283
Also known as Oriseal, Mark 2 and shut off valve at meter.
Use: Main shut off of water supply.
Sizes: ¾, 1, 1 ¼ 1 ½ & 2”
Features: Directional flowing valve. Port sealing O-ring that provides
positive shut-off and easy turning.
1/4 turn valve.
Pressure: 175psi
Connection options: Flare, Compression and FIPT
Installation: Inline on Copper, PVC or Poly-Pure Core. Below Frost line
(approx. 4ft). Accessible by Curb Box or PVC sleeve.
MFG. # B-20283
Use: Main shut off to water supply.
Sizes: ¾, 1, 1 ¼, 1 ½, & 2”
Features: Blow out proof
stem, double O-Ring seals. ¼ turn valve.
Pressure: 300 psi
Connection Options: Flare, Compression and FIPT
Installation: Inline on Copper, PVC or PURE-CORE. Below frost line (approx.
4ft). Accessible by Curb Box or PVC
sleeve.
MFG. # H-10310
Use: 1 ¼ - 2” Curb Stops, Except 2” Ball Valves(
can modify to fit)
Heights: 2, 2 ½ - 8’
*Carry instock 4’, 5 ½, and 7’
** Sold less rod
**OR**
MFG. # H-10314
Use: ½ - 1” Curb Stops
Features: Available with rod that can be attached to
Curb Stop key.
Lid can be removed with H-10322- 2’
key slotted, cast head.
Heights: 2’, 2 ½ - 8’
*Carry in stock 3 ½’ - 7 ½’
** Sold w/rod
MFG. # H-10284
Also known as Stop and Drain.
Use: Main shut off of water supply that allows water to drain out the
weep hole to eliminate freezing.
Size: ¾, 1, 1 ¼, 1 ½, 2”
Features: Same as Curb Stop but has weep hole on one
side.
*If installed backwards the valve will continuously leak.
Pressure: 175 PSI
Connection options: Flare, Compression and FIPT.
Installation: Inline on Copper, PVC or Pure-Core. Below frost line
(Approx 4ft.). Accessible by Curb Box or PVC sleeve.
MFG.# H-10013
Use: To tap a line and have shut off so you can run a supply line to
its destination. Once the line is
connected turn valve to open position and bury, there is no need to have a
sleeve.
Sizes: ¾,
1,1 ¼, 2”
Pressure: 100 PSI
Connection options: H-10013---MPT X MPT
H-10046—MPT X FPT
H-15000—CC X FLARE
H-15025—MPT-FLARE
MFG # H-15008—CC X CTS
MFG# H-15028-IPS X CTS 110 COMP
Mueller 110 comp. Fittings
MFG. # H-15428----MPT X CTS (copper tube size) 110 comp
H-15451----FPT X CTS 110 comp
H-15403----COMP X COMP 110 comp coup.
*This fitting is used on IPS PVC, Copper tubing and Poly Pure-Core.
IPS VS CTS: A black band is used on CTS. A red band is for IPS.
Installation: Tighten the compression nut until it makes metal to metal
contact. There is a light coat of
black paint on rim of nut that will be rubbed off when there is contact,
this allows user to know it
has been installed correctly. The gasket/gripper band being tightened
down will grove the pipe and his is what holds the connection
together.
Caution: Plastic pipe AND Pure-Core will collapse from the pressure it
is mandatory a stiffener be pushed into pipe.
Warning: Do Not reuse connection unless gasket/gripper band has been
replaced.
